Cut a piece of wire mesh if you need to clean a small area. The easiest way to clean decorative stones is to sift through a mesh with a mesh size of 13 millimeters. The cells of such a mesh have a size of 13 by 13 mm, so that the stones will remain on the surface of the sieve, and dirt and debris will sift through the mesh. A piece of mesh measuring 60 by 60 centimeters is quite enough for the job.
- If your stones are smaller than this size, then you can use a mesh with a mesh size of 6.5 millimeters.
Make a frame for the mesh out of wood for larger volumes. Use 5 x 10 cm boards (which you have on hand) to make a rectangular frame that is at least 0.35 square meters in size. The mesh should be cut to fit the frame and secured to the wood using strong staples.
- The sieve can be made of any size. This article suggests a minimum suitable size (0.35 square meters), but the area can be much larger. In some cases, it will be necessary to install wooden stiffeners across the mesh under the frame to prevent stones from pushing through the mesh.
Lay down a tarp to keep the yard free of debris. If you want to quickly collect dirt after cleaning the stones, then spread a large piece of tarp on the ground under the sieve. After work, you can simply lift the tarp and pour the garbage into a bucket.
- You can also immediately install the sieve on a large trash can.
Use a shovel to pour stones into the sieve. When everything is ready to go, start on one side of the area with the stones. Collect stones with a shovel and pour into a sieve. Be careful not to overload the sieve.
- Do not shovel soil with stones, otherwise you will only add more work to yourself.
Shake the sieve with your hands or move the stones with a rake. If you have a small sieve, you can shake it from side to side to remove dirt from the stones. In the case of a large sieve, to clean a large area, move the stones along the mesh using a rake. Dirt and debris will immediately begin to sift through the mesh.
- If weeds, brushwood, cuttings or other debris do not spill through the mesh, they should be removed by hand.
Place clean stones in a separate pile or return them to their place. There are 2 main approaches: you can immediately return clean stones to their place or put them in a separate pile to later distribute throughout the area.
- The first option may be a little faster, but you run the risk of sifting some stones more than once.
- You can also work in small sections, return the stones to their place, and then move on to the next section. Experiment to find the best option.
Clean the entire area with decorative stones. Divide the area into sections or move around the perimeter and then towards the center. The cleared sections will be noticeable even if the stones are put back in place immediately, as they will have a neater appearance and will not be packed as tightly as the rest of the area.
- If the area is too large to handle in one day, try sifting one section of the area per day until the job is complete.
Not a single representative of the fair sex can do without means that emphasize her charm and attractiveness. Among them, not the least place is occupied by jewelry - jewelry and costume jewelry, which provide many opportunities for the manifestation of the bright individuality of their owners. Modern jewelry made from natural stones Thanks to excellent processing and an abundance of designs, they allow you to bring to life any, even the most daring ideas for creating new images.
The online store of natural stones and jewelry “World of Beauty” presents an extensive collection for true connoisseurs. From us you can buy jewelry made from natural stones either separately or as a set:
- Earrings with natural stones
- Rings with natural stones
- Bracelets with natural stones
- Brooches with natural stones
- Pendants with natural stones
- Rosary with natural stones
Online jewelry store – buy at a profit
From time immemorial
Just think about the origin of the word “gem” and its deep meaning. Natural stones are called gems because their shade is given by nature itself. It cannot be artificially synthesized. Even the most accurate copies will still not be able to convey the full depth and richness of color that natural stones have, which you can buy in our store. But beauty and indescribable brilliance and radiance are far from their only characteristics. Since ancient times, stone jewelry has been considered not as simple decorative trinkets, but as talismans that can cope with all sorts of problems. Modest at first glance, turquoise is a real source of happiness, bringing prosperity and peace to every home. A passionate pomegranate can give its owner true love, help lonely people find a life partner, and even strengthen family ties. Amethyst strengthens relationships, promotes friendship, business contacts and success, protects against bad eyes and unnecessary worries. In short, each stone has its own role, history and purpose. Now if you want buy jewelry from semi-precious stones , they can be selected not only by appearance and your style preferences. Determine for yourself what task you would like to solve today, and the right stone will help you!
Gem store – shop without leaving home
Shopping with the help of the global world network will now surprise few people. Its popularity is only growing over the years, because it is much more convenient to make purchases remotely, avoiding queues, crowds, fuss and noise of usual retail outlets. Therefore, if you want to buy jewelry, an online store is a great option. Take a look at our comprehensive range. We have everything: jewelry, jewelry, which you can buy at the best prices, watches, ritual and folklore accessories - rosaries, shamballa, many cute little things - bookmarks, makeup mirrors, hairpins, bag holders, Gift Baskets. The online store offers you to buy all these products - jewelry, costume jewelry - on especially favorable terms.
Our prices– in the category of the most affordable, but for wholesale customers and organizers of joint purchases the cost of products is even lower. With us, jewelry, online store, retail or wholesale - always available!Why is our online jewelry store so popular?
A variety of stones, including passionate garnets, modest turquoise, delicate coral, mysterious amethyst, spectacular chrysoprase, exquisite pearls and an impressive list of others, no less beautiful and unusual materials, will make studying our catalog with photos a pleasant experience for you.
Our store represents so much a wide range of that every visitor can find a product in her favorite design and execution (for example, fashionable large beads or round earrings, rings with amber...), buy a beautiful and at the same time inexpensive jewelry for herself or loved ones. And, of course, most buyers return to the “World of Beauty” again for new things!
Designer jewelry made from natural stones - for connoisseurs of exclusiveness
If you are faced with the choice of buying handmade or factory-made jewelry, then most likely you will choose the first option. And this is not surprising, because designer jewelry always looks impressive and unique. In addition, the likelihood of seeing a similar set on someone is almost zero.
Excellent quality of finishing, variety of designs, originality of products, reasonable prices - thanks to these factors, the sale of jewelry and costume jewelry self made always popular.
“The World of Beauty” offers you to choose and purchase jewelry with delivery in Moscow and other regions. Study catalogs, choose, compare - we are waiting for your orders!
Despite its strength, stone is a very delicate material and requires care. This article provides recommendations for cleaning natural stone surfaces - how and what to wash it with. Even the types of stains are classified, because the choice of household chemicals depends on this.
General care
Place any glasses, especially those containing alcoholic beverages or citrus juice, on trays. Many drinks and foods contain acid that can corrode or discolor stone surfaces. Place hot dishes not on a stone surface, but on special mats. Place mats or napkins under porcelain, ceramic, or silver items that may scratch the surface.
FLOOR SURFACES
Sweep the floors with a dry, untreated mop or broom. Sand, dirt and abrasive particles cause the greatest damage to stone surfaces due to their abrasive properties. Rugs and mats on both sides of the main entrance will minimize the entry of sand, dirt and abrasive particles onto the floor that can scratch the stone floor, as long as the bottom of the mat is non-slip. Eight steps is usually enough to remove all the sand or dirt from the bottom of your shoes. Do not use used vacuum cleaners, as their plastic or metal wheels and attachments may also scratch the surface.
OTHER SURFACES
Clean stone surfaces using a few drops of cleaner, stone soap (available at hardware stores or from a stone slab supplier) or mild liquid dish detergent and warm water. For getting best results You need a clean cloth mop to wipe the floor and a soft cloth to clean other surfaces. Excessive detergent or soap may leave streaks. Do not use products containing citric, acetic or other acids on marble or limestone slabs. After cleaning, rinse the surface thoroughly with soapy water and dry soft cloth. Change the water often, do not use detergent powders or creams, since they contain abrasive substances that can scratch the surface.
BATHROOM AND OTHER WET SURFACES
In bathrooms or other wet areas, soap scum can be minimized by scrubbing the surface with a rubber brush. To remove foam, use an acid-free foam remover or an aqueous solution. ammonia, although the stone surface may fade if ammonia is used too often.
WORKING SURFACES
For work surfaces, a primer varnish may be needed. To prevent water marks from remaining, you need to treat the surface with non-yellowing wax in the form of a paste.
KITCHEN AREA
Here you may have to use a sealing compound or primer varnish that does not contain toxic components. Always consult the manufacturer.
COVERED Patio AND POOL AREA
In the pool, patio or hot tub area, rinse the surface clean water and use a mild bleach solution to remove algae or moss.
Properties of the stone
Natural stone comes in two types depending on its composition: siliceous or lime. Knowing the different properties of these stones is important when choosing cleaning products. Siliceous stone is mainly composed of silicon and quartz particles, is wear-resistant and can be easily cleaned with mild acidic cleaning solutions. Siliceous stones include granite, sandstone, quartzite, slate, ferruginous sandstone, and bluish sandstone (mica schist).
Limestone consists primarily of calcium carbonate. It cannot be washed with solutions containing acid, so it should be cleaned with products other than siliceous stone. Typical limestones are marble, travertine, limestone and onyx. A simple acid sensitivity test will help determine the type of stone. You will need 120 g of 10% hydrochloric acid solution or vinegar and a pipette. Since such an analysis can corrode the stone, perform this experiment on some remaining fragment. Apply a few drops of the acid solution to the surface of the stone. If the stone is calcareous, droplets of acid will begin to bubble or fizz. If no noticeable reaction occurs, then you are dealing with siliceous stone. Hydrochloric acid is a dangerous substance, so it is necessary to protect the surface of the skin from accidental contact.
Find out your stone
Granites and marbles are mined in different parts world and come in different color shades and with different mineral compositions. In most cases, marbles and granites can be identified by visible particles on the surface of the stone. Marble usually shows "veins", or a high concentration of minerals. In granite, minerals are typically visible as small specks evenly distributed across the surface of the stone. Each stone has a unique color, texture and mottling.
Sandstones differ greatly in color, due to the fact that the stone may contain various minerals and clays. Shades can vary from light gray to yellow or reddish. The dark red-brown sandstone is also called ferruginous sandstone. Bluish sandstone is a dense and hard stone with fine grains of greenish-gray or bluish-gray color.
Limestone- a stone widely used in construction with light gray, dark yellow or light brown shades. Feature many limestones - the presence of fossil remains in them, often visible on the surface of the stone. Slate comes in dark green, black, grey, dark red or multi-colored. It is most commonly used to make floor slabs, roofing tiles and has a distinct lobular texture.
Stone finishing
Polishing allows you to achieve a shiny surface that reflects light and emphasizes the color and texture of the material. Similar finishes are used for walls, furniture and floor tiles.
Polished texture- This is a smooth, satin surface that reflects light relatively poorly. Overall, the honed finish is ideal for floors, stair treads, porch steps, and other high-traffic areas where the polish can quickly dull. Polished texture is also used in furniture and for finishing other surfaces. Fire finish is a rough textured surface often seen on granite floor slabs.
Stains
SPILLS AND STAINS
Immediately blot up any spilled liquid with a paper towel. Do not rub this area as this will only spread the spilled liquid. Wash the area several times with plain water and mild soap. Dry thoroughly with a soft cloth. Repeat the procedure if necessary. If the stain remains, refer to the stain removal section.
STAIN REMOVAL
Identifying the type of stain on the stone surface is the key to removing it. If you don't understand what's causing the pollution, try playing detective. Where is the stain located: near a plant, a food preparation area, or a bedroom where cosmetics are used frequently? What color is the spot? What shape or pattern is it? What happens in the area around the spot? Surface stains are often easily removed with a cleaning product or household chemicals. Stains that are deeply embedded in the texture of the stone or cannot be cleaned with conventional cleaning products may require special sealants or professional intervention.
Types of stains and the first steps to remove them
OIL BASED (FAT, TAR, BUTTER, MILK, COSMETICS)
An oil stain causes the stone to darken and is usually dissolved by chemicals and then washed away. Gently wash the area with a mild, liquid cleaner containing bleach or household detergent. detergent, or ammonia, or varnish solvent, or acetone.
ORGANICS (COFFEE, TEA, FRUIT, TOBACCO, PAPER, FOOD, URINE, LEAVES, BARK, BIRD LOODS)
Usually results in a pinkish-brown spot, but it may disappear once the source is eliminated. Regular rain and sun will whiten and remove such stains on the street. In the room, you need to treat the stain with a 12% solution of hydrogen peroxide, and also drop a few drops of ammonia on it.
METAL (IRON, RUST, COPPER, BRONZE) Rust stains range in color from orange to brownish. They can take the form of sources of contamination such as bolts, screws, tin cans, flower pots, metal fittings, etc. Copper-bronze stains have a greenish or dirty brown tint and are caused by exposure of nearby copper, bronze or brass products. Metal stains must be removed using a special putty or stain removal paste. It is extremely difficult to remove deeply ingrained rust.
BIOLOGICAL FORMATIONS (ALGAE, POWDERY MEW, LICHEN, MOSS, FUNGI)
Rinse with a solution (half a cup per 3.5-4 liters of water) of ammonia, or bleach, or hydrogen peroxide. Do not mix bleach with ammonia! When they combine, a toxic and deadly gas is formed.
INK (FELT PEN, BALLPOINT OR INK PEN)
Wash with bleach or hydrogen peroxide (light-colored stones only!) or lacquer thinner or acetone (dark-colored stones only!).
PAINT Small amounts can be removed with lacquer thinner or gently scraped off with a razor blade. Thick layers of paint can only be removed with a commercial paint stripper solution, which can be purchased at a hardware store. These solutions usually contain caustic soda or lye. Do not use acids to remove paint from stone. Paint stripping solutions can corrode the surface of the stone, requiring re-polishing. Follow the manufacturer's instructions and remember to rinse the stained area thoroughly with clean water. Protect your hands with rubber gloves and your eyes with special goggles and work in a well-ventilated area. Use only wooden or plastic scrapers to remove tar or paint clumps. Usually emulsion and acrylic paints do not lead to surface contamination. Oil stains can appear when using oil paints, linseed oil, mastic, sealants and sealants.
DROPS AND RINGS OF WATER (SURFACE ACCUMULATION OF HARD WATER)
Polish with a dry iron brush.
FIRE AND SMOKE DAMAGE
Older stones and fireplaces with signs of smoke or fire may require more thorough cleaning to restore the original surface. Commercially available smoke removal products can save time and effort.
TRACES OF CORROSION
They can be caused by acid remaining on the surface of the stone. Some materials may corrode the coating but not leave stains. Others corrode and stain the surface. After removing the stain, rinse the surface with clean water and apply polishing powder, available at a hardware store, to the marble. Rub the powder into the stone with a damp cloth. Polish until the mark disappears and the marble surface begins to shine again. Any marks that you cannot remove should be treated and removed by a professional polisher.
EFFLORESCENCE
Efflorescence refers to a white powder that can appear on the surface of a stone under the influence of water containing mineral salts seeping from under the surface of the stone. Water passes through the fibers of the stone and then evaporates. When it evaporates, it leaves a powdery substance. If the slabs have been laid recently, wipe the area with a mop or remove the powder with a vacuum cleaner. You may need to do this process several times as the stone dries. Don't try to wash the powder off with water because it will only disappear for a while and then come out again.
SCRATCHES AND CRACKS
Small surface scratches can be removed with a dry iron brush. Deeper scratches and cracks on the surface of the stone should be repaired by a professional who will restore the polish.
Putties or pastes: how to use them
Putty is a liquid cleaning agent or chemical mixed with a white absorbent material. The result is a paste with approximately the same consistency as peanut butter. A layer of paste 0.6-1.2 cm thick is applied to the contaminated surface with a wooden or plastic spatula. Then this area should be covered with plastic and left for 24-48 hours. The liquid cleaner or chemical will draw the stain into the absorbent material. This procedure may need to be repeated several times to completely remove the stain.
Materials for stain remover
These include kaolin, fulling clay, whitewash, diatomaceous earth, ground chalk, molding plaster or talc. Per square meter you need about four kilograms of stain remover paste. Do not mix whitewash or fulling (iron) clay with acidic chemicals, otherwise they will react and the effect of removing stains will be negated.
Cleaning products or household chemicals
OIL STAINS
Requires an aqueous solution of soda (sodium bicarbonate) or one of the powdered putty substances and varnish thinner.
ORGANIC POLLUTANTS
Cover the stain with one of the powder paste materials and treat with a 12% hydrogen peroxide solution or replace the hydrogen peroxide with acetone.
RUST
Cover the stain with diatomaceous earth and a commercial rust remover. Rust stains are difficult to remove and you may need to call in a professional service.
TRACES OF COPPER
Cover these areas with one of the powdery, paste-like materials and add a drop of ammonia.
BIOLOGICAL FORMATIONS
Apply a solution of ammonia, or bleach, or hydrogen peroxide. Do not mix bleach with ammonia.
Prepare the putty.
If you are using a powder, mix the cleaning product or household chemical until it becomes a thick paste. If you use paper, soak it in a chemical solution and let it dry, do not apply it in liquid form. Rinse the affected area with distilled water. Apply a layer of putty 0.6 to 1.2 cm thick: you should cover the stain and coat the surface around it at a distance of 2.5 cm from the stain. Spread the paste evenly with a wooden or plastic scraper. Cover the putty with plastic and seal the edges with duct tape. Leave the putty to dry for 24-48 hours. As the stain dries, it will be pulled out of the stone and into the putty material. After about a day, remove the plastic and let the putty dry further. Then you need to carefully remove the putty from the stain, rinse the area with clean water and wipe with a dry soft cloth. If necessary, use a wooden or plastic scraper. Repeat this process up to five times until the stain is gone. If the surface is corroded by a chemical reagent, apply polishing powder and rub with a jute cloth.
Regardless of what the gem is used for (for medicinal, magical purposes or as decoration), it needs to be cared for and sometimes cleaned. When you buy a stone, you need to clean it. Keep it under running water for a few minutes. It is better, of course, if possible, to use natural spring water.
Minerals that belong to the quartz group can be placed in a glass bowl with water and kept overnight in the freezer. You can place stones and products made from them in a vessel with water. The water, when frozen, will remove dirty information from the stone, and it will be cleansed. In this way, you can clean both stones that you previously wore and new ones - purchased or given as a gift.
In the same way, not only newly acquired stones are cleaned, but also those that you already have. This should be done at least once a year, and health stones are cleansed once a month on the waning moon.
The general rule for cleaning stones is this: it is always better to clean all stones in the last three days of the lunar month (28, 29, 30) - before the new moon. During the full moon, stones accumulate energy and after cleaning they should have time to restore their own energy.
Tourmaline.
To store stones, it is best to use bags for each stone separately. The bag should be silk or cotton, or linen. In such packaging, gems can be stored in one box or box.
There are several methods for cleaning and renewing natural stones (it must be clarified that not all methods are suitable for certain minerals). Precious stones have different properties and require an individual approach to cleaning. While for some it is appropriate to use a soap solution, for others it can be disastrous. Improper cleaning can ruin your favorite piece of jewelry.
- Cleaning with water - the stone is kept under running water (from the tap) for several hours. It’s better to put it in a bag and into a spring, tie the bag so that it doesn’t get carried away. Or just pour spring water into a glass and put a stone in it.
- Cleaning by the sun - first wash the stone with water and place it in bright sun for 30 minutes. This is both cleansing and charging the stone.
- Cleaning with salt - bury the stone in salt for 3-4 hours, then throw away the salt.
- Cleaning with a saline solution of water - immerse the stones in salted water poured into a crystal bowl. It can also be used in other containers, of course.
- Cleaning with soapy water - prepare a warm soapy solution, pour it into porcelain or crystal dishes, and leave the stones in the sun for about two hours,
- Cleaning with earth - bury stones (this applies to cleansing precious stones) in the ground overnight.
- Cleaning with natural sea water - wash the crystals with sea water and leave in it for 3 hours.
All the stones from time to time it is useful to expose it to sunlight for several hours or days. This especially applies to those stones that you constantly wear. But - be careful - some stones change or lose color in the sun.
You can just wash the item with water every day - the stone will only get better.
If the hardness of the stone is above 5 ( sapphire, emerald, diamond, topaz, ruby, aquamarine, quartz, ordinary beryl), then cleaning in a solution of any washing powder using a brush is allowed. An exception would be jewelry that uses soft metal, for example, silver.. Gems framed in gold or platinum will respond well to such cleaning. After cleaning, rinse off the remaining solution with distilled water.
For cleaning stones, a solution consisting of 120 g of baking soda, 30 g of table salt and 50 g of bleach, dissolved in 0.5 liters of water, is suitable.
Gemstones are often very fragile and can easily crack if handled carelessly. This is especially true for those stones that have inclusions. Therefore, if you want to clean peridot or emerald yourself, be very careful! A wrong movement and a piece may break off from the stone.
Gemstones with a hardness level below 5 should be washed in a milder environment, such as soapy water. These stones include - apatite, ruby, opal, sunflower, moonstone, peridot, lapis lazuli, malachite.
Ruby, alexandrite and sapphire can be cleaned in a soapy solution with ammonia. The proportions of the solution are 0.5 cups of water, 1 teaspoon of alcohol. After cleaning, rinse the gems with warm water.
Amethyst, rock crystal and citrine should only be cleaned using ultrasound.
Turquoise- a capricious gem. It cannot be cleaned with aqueous solutions; their influence can easily cause the stone to lose color. Turquoise jewelry should not be exposed to sudden temperature changes or exposure to acidic or soapy solutions. To remove heavy stains, alcohol or distilled water can be used. To restore shine, a piece of flannel fabric or dry suede will do - you can polish turquoise with them yourself.
Very often dirt collects under a stone. You can remove it with a match and a piece of cotton wool. Moisten cotton wool with glycerin or a solution of magnesia and ammonia. Use gentle circular motions to rub into recesses and surfaces. If there are still particles of dirt that cannot be removed, contact a jewelry cleaning professional. May need professional cleaning using ultrasound. True, not all stones can be cleaned with ultrasound.
A universal way to clean any stones
Amethyst druse.
Minerals are put in overnight on an amethyst druse with very small crystals (also called amethyst brush or stone bed).
Also known cleaning with quartz druse- place the stones on the quartz druse overnight.
What should you do if a huge scandal suddenly breaks out at work? Immediately remove negativity from yourself and your jewelry!
Everyone knows that stones, and especially crystals, have one important feature– accumulate energy and information. This property requires periodic cleaning of all natural stones and jewelry.
New stones must also be cleaned. Moreover, it does not matter at all how the gem came to you - whether you bought it in an esoteric store, ordered it online, or whether it was given to you as a gift. Any stone requires cleaning before you start using it and, of course, with frequent use.
The best cleaner from negative information is water. It is enough to hold the stone for a short time under running (or better yet, spring) water, and its energy structure will be completely freed from negative and previous information. This is one of the simplest and most versatile methods that easily copes with the cleaning task.
What else is used to energetically cleanse stones?
To energetically cleanse stones, use:
- fire
- salt (sea or regular)
- Druze (rock crystal or amethyst)
- herbs and flowers
- Moonlight
- sunlight.
Salt
Cleansing natural stones with sea salt can be considered traditional and one of the most the best ways cleaning the stone, since sea salt simultaneously cleanses both household pollution and accumulated negative information. Sea salt, which naturally evaporates in the sun, is simply an invaluable storehouse of useful and, most importantly, “living” active minerals, which certainly interact with the stone, cleansing its energy structure and taking on all the negative energy.
In this case, you can choose both dry and wet cleaning methods with salt.
Wet cleaning
Dissolve a teaspoon of sea salt in a glass or ceramic cup of water. Plastic and metal dishes are not suitable, since these materials transfer some of their properties to water. To make the salt dissolve better and faster, fill it with warm water. But the stone can be lowered into the solution only after it has cooled! Most natural minerals are extremely poorly tolerated high temperatures: may crack or change color. The stone must be immersed in the solution overnight. In the morning it should be rinsed under running water.
Dry cleaning
For dry cleaning, you will need a deep container because you will need to pour enough sea salt into it to completely cover your stone. Any utensil can be used. Dry cleaning of the stone using dry sea salt is also carried out overnight.
Attention! High-quality polished jewelry stones may fade when exposed to sea salt, and some may change color. But don’t rush to give up this type of cleaning.
Alternative way cleansing stones with sea salt: place the stone in a glass bowl and place it on a dish with sea salt (salt layer - at least 1 cm). Despite the fact that the stone will not actually come into contact with sea salt, it will still certainly have a cleansing effect on it.
Which stones should not be cleaned with salt water?
Here is an incomplete list of them: amber, malachite, onyx, opal, pyrite, aquamarine, turquoise, hematite, labradorite, calcite, cacholong, lapis lazuli, rhodonite, rhodochrosite, carnelian, fluorite.
Salt water has a negative effect on their physical properties. If your stone is not on the list, but you have doubts and are worried about the consequences of contact of the mineral with salt water, use dry “non-contact” cleaning using sea salt.
Fire
The most suitable time for carrying out procedures for cleaning stones with fire is when the Sun enters Aries (1st ten days of March - from 21st to 30th March). According to astrologers, all stones and jewelry passed down by inheritance need to be cleansed with fire.
Place the stone on the table, take a lit candle in your right hand and perform circular movements clockwise (if a male stone, Yang energy) or counterclockwise (if a female stone, Yin energy).
During the procedure, you can mentally say “cleansing” words: “ Burn in fire everything that harms me.".
After purification by fire, it is recommended to leave some minerals in direct sunlight for several hours. Almost all stones benefit from sunbathing, especially those that are often worn. For some stones (coral, turquoise, pearl, opal, amber) solar treatments must be limited in time: no more than 30 minutes per session.
Moonlight
The moon is most directly related to the magic of stones, since it heavenly body has the most direct physical effect on all living things on Earth.
And moonlight has a fantastic effect on natural minerals.
The procedure for removing negativity from a stone using moonlight will take you longer than all the others. Here it is necessary to take into account the phases of the moon. It is necessary to carry out the cleaning procedure only on the waning Moon, since as the Moon wanes, it will take with it all the negativity. In addition, a lot depends on the weather - the sky is not always clear. Therefore, sometimes you have to wait a long time for the right night to clear your stone. On top of that, you will have to find a window sill or a place that will be flooded with moonlight for the maximum amount of time throughout the night.
To completely remove all negative energy from a mineral, it will take three full lunar nights. If you can leave the stone or decoration outside, this is certainly an ideal cleaning option. The glass on the windows, however, slightly blocks the light of the “queen of the night sky.”
If the stone has been subjected to a very strong negative influence and is not afraid of water, it is necessary to lower it into a vessel with salt water and leave it for several nights on the waning Moon.
Herbs and flowers
This is a very beautiful and delicate way to cleanse natural minerals from negative energy. Immerse your stone or jewelry for the day in a container with dried or fresh herbs or fresh flower petals. To enhance the cleansing effect, it is recommended to combine this cleaning procedure with moonlight cleansing.
Fumigation is very effective method cleaning stones from negativity. To do this, you need to set fire to some medicinal herbs in a fireproof container. Sage, cedar or juniper are ideal. The stone must be carried several times through streams of smoke. Thick clouds of smoke are not needed for this; a weak, thin smoke will do. To calm the energy of the mineral, add a few lavender flowers.
Remember that cleaned stones should not be given into the wrong hands, even those closest to you. Human energy is too complex and subtle. Therefore, you should not take risks, protect your stones.
But what to do if you were asked to show or try on a stone or jewelry by loved ones? In many cases, it is inconvenient to refuse such a request, so as not to offend a loved one. Then place the stone first on the table so that it is taken not from your hands, but from the table. You need to take your stone back in exactly the same way - only from the table, and not through your hands. This will prevent the transmission of other people's vibrations into your biofield. If such a manipulation was not possible, and the jewelry was nevertheless transferred “from hand to hand,” simply carry out an additional cleaning session.
Druze
It is very easy to remove negativity from stones and jewelry using druzes.
A druse is a set of fused crystals. This form is the strongest emitter and transformer of energy. Druse has only the most positive effects on the environment and is excellent for cleaning stones and the human aura.
Stones or your favorite jewelry that you wear every day, and on which a lot of negative information accumulates, are placed on a rock crystal or amethyst friend at night. Already in the morning the minerals will be crystal clear! Amethyst and crystal druses are ideal for cleansing procedures; it is not for nothing that magicians and lithotherapists call them “amethyst brush” and “crystal brush”. Stones and jewelry are very well cleansed from negative information with the help of druzes during meditation.
As soon as you get your hands on a new stone, you need to clean it immediately, on the same day! One of the best ways is to leave the stone to bask in the sun for 2 hours. As already mentioned, an excellent way to remove negative information from a mineral is running water. If there is a river or stream flowing near your house, place a stone in it for a while. Streams of water will carry all the negativity far and irrevocably. In a couple of hours, your mineral will be pristine in terms of energy. It is not recommended to clean new stones in salt water, as this can lead to premature wear.
Crystals that are contraindicated in contact with water
As you know, turquoise does not like water. You can wipe and wash it, but such contact must be kept to a minimum. The ideal care for turquoise is to wipe with a dry soft cloth after each use.
It is necessary to exclude contact with water of such minerals as: chrysocolla, astrophyllite, heulandite, gypsum, kyanite, muscavite (a type of mica), selenite, seraphinite (clinochlore), stilbite, uvarovite, celestite, chermigit (geyserite), fuchside slate.
These minerals dissolve under the influence of water, and even with slight contact with liquid they begin to lose their physical properties. Remove negative information from such natural materials best using candles or any other dry methods.
How often do you need to remove negative energy from a stone?
This depends on the intensity of its use and on the energy load that the mineral carries. For example, if you wear your favorite ring and ring with a large mineral every day to the office, where you are surrounded by many ill-wishers, then the jewelry simply needs to be cleaned as often as possible, every weekend! And if a serious conflict occurs that knocks you out of your psychological balance, the stone needs to be cleaned immediately! And after the cleaning procedure, it is necessary to leave it to “charge” for a long time, until the entire negative matrix leaves its information grid. After conflict situations, deep meditation with natural stones. You need to meditate with minerals that are used only in spiritual practices and practically do not carry information from society.
Find out more: How to choose stones for meditation.
If you often change your jewelry and do not overload it with negative energy, then you can clean it once a month or less. Sensitive people, who have the ability to enter into full energy exchange with natural minerals, determine the need to clean the stone intuitively, according to their feelings. If you feel that your favorite pebble has lost its energy, then it’s time to “remove” unnecessary information from it.
